Bath - is a place where you can wash away all worries and relax the whole body.If you make a bath with his hands, with only a little effort and you can bathe and take water treatments.But the interior bath, shower and changing room design is a very important process, and it should be taken seriously.
choice of material for the steam ↑
The most important thing in the finishing bath - is the adoption of a decision on the material.One type of wood bath is best not to finish: for a variety of space baths should choose a different breed.To see this again, c
The cheapest material is considered to be a pine, but paired her best not to apply.In its wood contains resin.At high temperatures in the bath, they are beginning to stand out, tread on the surface of the wood.The steam thus be impossible.
For the best steam acts linden wood.If the sheathing lime bath, you can be sure that just will not burn, because the material to such a degree does not overheat, and the color is retained.There are other options for finishing baths - for example, aspen, birch, poplar.They are durable, so faithfully serve more than one year.
Any of these breeds would be appropriate in the bath than pine.Hardwood well and dries quickly, it is important to create a pleasant climate in the bath.Each type of wood has its beneficial properties.Lipa human body charges a positive energy and is capable of pulling aspen sickness and negative emotions.
that you should not use ↑
Interior finishing bath should not be performed with the use of wood-based panels and linoleum.They were strictly forbidden to use the steam room and washing room, because such work can be bad for the health of people hovering.
Materials such as chipboard, hardboard, mineral wool, are flammable and toxic when heated.They greatly swell when moisture absorption.Linoleum on heating and release harmful substances into the atmosphere, is afraid of high humidity and quickly rots.
All of the above described restrictions apply only to areas with high humidity or temperature.They may well be used, furnished relaxation room.There is no humidity, and the temperature is not too high to cause evolution poisons in air.
Warming and finishing the ceiling and walls ↑
to create a seal in the steam room should perform thermal insulation mineral insulation that harbor the aluminum foil from the effects of steam.The edges of the foil must be connected to a special tape.The film was not used due to the high temperatures under the influence of which it can be deformed.Finishing bath outside implies block the vents.
The ceiling is made of planed board thickness 20 - 30 mm.Boards attached to the joists with nails.The length of the nails should be selected so as to be 3 times longer than the thickness of the boards used.For ventilation in the steam room it was worth to round the sharp edges of boards and leave a gap of small size.
Molded - the best material for covering ↑
Despite the abundance of materials that are suitable for interior cladding buildings baths, the most popular of them was still lining.Its relevance is explained very simply.Finishing bath paneling solves two problems at the same time - warm and decorate the walls.
material made of wood and consists of a paneling.The walls, which are decorated with clapboard, look beautiful, as the panel visually level the surface.Sort the information on the World Wide Web at the request of "finishing baths video" and you'll understand everything yourself!
Molded extremely practical because it improves air circulation in the sauna: walls can "breathe", which in turnturn prevents condensation, mold and mildew, as well as allows you to adjust the relative humidity in the bath.As stated above, the steam room is great linden tree, so often used for baths lime linings.
Preparing for decoration of the walls ↑
technology finishing bath paneling - quite simple and straightforward!Before the start of construction linings contribute to the steam room to timber adapted to the climate.
If there are noticeable differences walls, they must be aligned.If you do not align the bulge, the rails are locked at various levels, and will receive the waves on the walls.Therefore, it is important to prepare all surfaces.
Molded directly onto the wall mounted large construction staples or screws.However, as a rule, have a surface distortions and irregularities, so the risk in this case is not justified, and it is better to set the crate.
Crate: build or not?↑
work should start with the installation of lathing, which make with slats measuring 20 by 40 millimeters.Further slats should be installed on a distance of 50 - 100 centimeters from each other.The first step is to secure the extreme bars, focusing on a plumb and level.Then they should fix the mounting thread, and then taken to fix the remaining slats with screws.
Crate may not be installed.Fixing material, in this case on a wall surface.But for such a bath interior wood was durable, beautiful and durable, it should be made perfectly smooth wall.
Plating baths clapboard walls ↑
After the preparatory phase, begins wall decoration in the bath.We need to pick up the fixings.It is necessary that they be made from materials that do not react on exposure to high humidity and temperature.Conventional nails should forget, because they corrode give rust streaks on the walls and heating can burn the skin.
material should be cut to the size of the height of the bath, and then attach it to the grid prepared by special finishing nails or staples-klyaymerami.If the requirements for angular joints battens should be lightly trimmed in width.
Finish floor in the steam room ↑
Interior finishing bath with his hands starts with sex.And in the steam room floor better pick.It is necessary to make higher than in other floor areas 15-20 centimeters.This must be done to prevent drafts and retain heat better.Sex is better to lay out tiles, decking or trim boards.
boards have to be laid on wooden joists that are placed on columns of brick section 0.25 to 0.25 m. The bars are placedon the sand or concrete base.The edges of the boards should be round, leaving small gaps between them.This will facilitate the operation of cleaning the premises.Boards fastened directly on the surface or the prepared crate.
for fixing common nails impractical to use because they are quickly destroyed by corrosion.Finishing bath with his hands made with galvanized, bronze, brass or stainless steel fasteners.
shelves and benches in the steam room ↑
in the steam room should be a good solid shelves, chairs and benches.It is best to make their round shape, more importantly, that they are firm and do not creak.Thoroughly should consider the choice of wood.
sunbeds should not have knots, preferably soft wood with a low density, which is not very hot.The most economical option - aspen, more expensive - lime.Fans pine aroma in the steam room near the furnace is recommended to attach the boards of cedar.
The bath can be positioned several shops, setting them on the wall, which has no windows.Shelves should be made of different sizes: the bottom shelf - the smallest, about 30 centimeters;average - 60 cm;top - the widest, about one meter.
dressing room: the rules of arrangement ↑
If we talk about the waiting room, there is pine paneling welcome.The walls are not too hot, the resin does not act, and finishing that is made of pine, the room is filled with healthy pine aroma.
known that softwood highlights many volatile production, which positively affect the well-being of man and are beneficial to the body's resistance to various infectious diseases.
specifics of finishing the washing compartment ↑
Finish bath with his hands in the washing compartment requires coniferous tree species.It is pine, cedar, fir, spruce.The walls in the bathroom can be finished larch.The temperature in the washing room is much lower than in the steam, but the humidity is often much higher.Given this, the floor is necessary to make a coating of tiles.But this material has one major drawback - tiles slippery, so you need to protect the movement in the shower on this floor.
C above described purpose is to make wooden trapiki who decided to manufacture small and light.If necessary trapiki can be easily taken out of the washing compartment and dry.Decorating the walls of the shower can be made of pine boards or other inexpensive wood.
Video: arrangement bath ↑
wishing to decorate a bath with his hands a lot of valuable ideas will prompt material video:
Thus, Russian bath a combination not just a normal bath with a steam room, an ancient tradition of cooking steam, colorful decorationsand interior wood, which includes the design of the walls, floor and ceiling, as well as various furniture - shelves, beds, benches.