Answer: In the classical garden with clipped borders and other elements of regularity, which features sculptures and small architectural forms, where the front of the house is decorated with columns, is appropriate rather massive smooth stucco or brick fence, supporting pillars which are similar in shape to the columns of the building.
log house better surround palisade or imposing wooden fence, covered with "lining" of the building - lighter structures, say picket fence.Brick house it will require a proportional height and massive brick or stone wall.
The color fence can be tied to the walls, the roof of the building, walkways, small architectural forms.
Question: How deep digging holes to install fence posts?
Answer: Pit under the fence should be drilled to a depth of 10 cm more than the installation of racks.Then there will be an opportunity to install them on the same horizontal line and eliminated the need
Question: What should be the supporting pillars of the fence the villa?
Answer: If decorative appearance fence depends largely on the design spans, for the strength of the structure is very important to choose the material supporting pillars (also called pillars).The support pillars are usually made of metal (steel tube of square, rectangular or circular section with a diameter of 50 mm) or concrete (good, if four racks have vertical reinforcing rod instead of two).
Q: What are the requirements for the installation of wooden fence struts?
Answer: Stands must have a minimum diameter of 14 cm and a length of at least 2.3 m. Was immersed in the land of the rack is protected from rotting daubing with heated bitumen or roasting in the fire to the coal layer.Deviation vertical uprights as well as their position in terms should not exceed 10 mm.
Q: How to make a fence from a wire?
Answer: It can repeat the terrain.The wire is fixed on poles parallel rows of not less than 25 cm. The tension of the wire is made to the disappearance of deflection.In order
hardening barriers in each section further performs cruciform cross-wire.All intersections of parallel rows with cross constrictions must be connected binding wire.
Q: How many bricks will need for the construction of the fence?As the fence is built of brick?
Answer: brick fence spread thick and 1 1/2 bricks.On 1 m² wall thickness of 1 110 bricks need about bricks and 1 m2 wall in 1/2 bricks - 55 pieces.Masonry mortar recipe: 1 part cement and 4 parts of fine washed sand.Since
brick wall hard enough erection, it will take the foundation.As a rule, the strip foundation, which is a trench filled with concrete mortar.For fences up to 80 cm dig a trench depth of 10 cm for higher fences - up to 20 cm. The concrete for the foundation is prepared at the rate of: 1 part - cement, 4 parts - coarse sand and 4 - rubble.
When building a brick fence every 2-3 rows of masonry must be reinforced with a special mesh.It is important that brick wall was strictly vertical, corners and complex geometric areas are processed correctly, and the seams - embroidered correctly, otherwise under the influence of precipitation bricks begin to crumble.
between the foundation and the fence is necessary to pave the waterproofing (common roofing material in 1-2 layers), or of the land will continue to catch up the moisture and bricks begin to crumble as a result of seasonal freezing and thawing of water in the pores.
To protect against rain and snow over the spans and poles are usually installed visors (metal or concrete).
Q: What feature stone walls?
Answer: The use of stone, as well as brick, distinguished by durability and strength.Moreover, their decorative appearance fits perfectly into the landscape of the site.The material usually used cobblestone, limestone, sandstone and coquina.Good looks of hewn stone wall or rubble.The thickness of the masonry must not be less than 40 cm, and every 8-10 m is necessary to put the supporting pillars.Like brick and block fence, a wall of natural stone requires a thorough strip foundation.
Question: What technology devices villa fence of mesh-netting?
Answer: Put a fence grid is simple enough.It is mounted on metal, concrete or asbestos cement pillars, and its or nailed to the bars or pull with a steel wire.Buying grid, note the difference between the net for plastering and mesh for fences.The plaster has a much smaller cell (10 mm) and made of a thin wire (diameter 1 mm).It is better not to use one instead of another, but even if you make a mistake, do not worry: the plaster mesh fences are long enough.
mesh for fences by type coating can be divided into three types: conventional (known as black), galvanized and coated net.
most simple and cheap, of course, black-mesh netting and black welded (cost from 30 to 50 rubles. For 1 m², depending on the mesh size and wire diameter).They require mandatory thorough painting immediately after installation in the future will have to paint it about once every 3-4 years.Galvanized mesh and mesh coated paint is not required, but are more expensive by about 30 and 70%, respectively.The service life of mesh-netting even neozinced significantly exceed 30 years.
Q: What are the advantages and disadvantages of the metal sections of the fence?
Answer: Metallic sectional fences are manufactured in the factory and assembled on-site metal poles or bolt, or by using the welding machine.Advantages of these hedges are undeniable: they are with minimum maintenance (periodic painting), very durable, resistant to mechanical damage, and look good.The lack of one - a few such designs pricey (200 rub. / M), especially if you need to enclose a large plot.
Q: What is plastic fence?
Answer: In appearance, plastic fences resemble wood.At the height can reach 6 m. The building consists of four types of elements: columns, horizontal runs, vertical panels and visor parts.All are made of thick hard PVC foam, colored in various colors.
Plastic fence built as children's designer.The pillars are at the base of the shoes, which are attached to the concrete base with anchor bolts.By the posts, in turn, is mounted horizontal beams, and to them - vertical panel.Posts and cross inside a metal reinforced reinforcement.This fence does not require painting, it is very easy to clean, does not rot or rust.Manufacturers guarantee that within 25 years of their production does not darken and not burn out.Operating temperature range - from -30 to +50 ° C.
Question: How is arranged soundproofing fence?
Answer: One of the options for acoustic barriers - installation of sandwich panels.Their outer surfaces - a metal corrugated roofing sheets, between which mineral wool boards or Penoizol (total thickness - 140-190 mm).This panel simultaneously reflects and absorbs the sound, that is playing the role of a full noise protection system.
construction height is calculated in a specific pattern: between two points - the tip of the roof ridge and the highest point of the alleged finding of trucks on the road - held an imaginary line which should overlap the fence.The upper part of the structure is required to be equipped zvukootboynikom.
Another option - the creation of a reflecting surface of the stone.The basis of the fence in this case can be made of foam, but used for lining stone - natural or artificial.His deliberately placed unevenly, imitating slate surface.The smaller and more frequent irregularities has a wall, the more noise it dissipates.
Finally, the third option - using a monolithic (no cell!) Polycarbonate sheet with a thickness greater than 8 mm (the price - 25-30 / m²).This material has some good sound absorption properties and also very durable.To create a more interesting from the point of view of the decorative structure polycarbonate can be combined with tree.
material prepared L. Rudnicki, A. SAHIBZADINOV, E. Abishev