Gates from corrugated board

By Admin | The Hands
20 May 2016

After the erection of the fence it's time to install the gates and wicket.How to easily install the gate, he will describe in this article, and the gate is similar to going to the gate.

First of all, the loop fixed on poles, 10delta put on a previously prepared left and right goalpost.Between the goal posts and pillars he set gaskets and pressed them to each other clamps.Then measure the distance between the upper goalposts, cut the pipe at this size and grabbed her by welding.The same thing he did with the lower tube.

In the next stage, he found the center of the upper and lower horizontal pipes, departed from him on both sides of 3 mm.Then measure the distance between the upper and lower pipes, gates and cut on the size of the two tubes that are set in the middle of the gate on the marked distance in the vertical position, department, so the two halves of the gate.

Then at the bottom of the gate, he welded a horizontal pipe for installation cutting.Finally, the finished frame tubes in the center

of the gate halves.At the center of the goal line, above and below, he did through slots, gates separating grinder into two halves.

After that, with the help of friends, he took the two halves of the gate, put on a horizontal surface and thorough boil and handled all seams, cut off the excess tubing.Finished frame 10delta paint over paint.After the paint has dried, he established an internal frame, attaching pre-painted metal pipe with screws.The same screws attach the metal strip on one of the gate leaves (in order to close the gap between the doors).After all these operations it is to paint over the gate leaf a second time.

Then he cut corrugated required size and fasten it to the side of the gate aluminum rivets 4,0h6mm and die-cutting rivets 4.8h10mm do not forget to lay the washer.

Bolts

For doors 10delta wanted to buy ready-made bolts, but did not find anything suitable and decided to make them myself.For this he cut piece 3 from the correct size band width of 4 and a thickness of 3 mm and made from residues guide tubes.Produce pin, inserted it into the guide and weld them to the metal strip.

assembled structure he painted and hung to dry.After the paint has dried, he made the bars attached to the gate.Then he called friends and hung gates.With the help of a drill to make a hole to a depth of half a meter to the pipe inserted, which will include bolts and concreted them.And in the end he hung a mailbox on a fence at the entrance.


estimates for the construction of the fence

  • square tube 20x20 / 2 mm (for internal framing of doors and gates) - 42.3 n / m - 1846 rubles .;
  • square tube 60x60 / 2 mm (for fence posts) - 51 n / m - 6050 rubles;
  • square tube 40x40 / 2 mm (for frame doors and gates) - 42.3 n / m - 3841 rubles .;
  • square tube 80x80 / ​​2.5 mm (for the posts of the gates, and the gate) - 11 n / m - 2638 rubles .;
  • square tube 15x15 / 1.5 mm ("antizaglyadyvateley") - 9 n / m - 360 rub .;
  • square tube 30x30 / 2 mm (horizontal bars) - 125.6 n / m - 7410 rubles .;
  • Profiled C-8 / 2000h1200h0,5 mm (intake from neighbors, aluminum-zinc) - 18 pcs.- 7733 rubles .;
  • Profiled C-8 / 2000h1200h0,5 mm (front, chocolate-colored RAL8017) - 24 pcs.- 12557 rub .;
  • metal band.40h4 (for gate leaf and the gate) - 6 m - 240 rub .;
  • Cutting 240h1996h3 mm (for the air holes in the fence) - 25 pcs.- 2650 rubles .;
  • Additional elements (sills, corners) - 2284 rubles.
  • Delivery (total) - 1000 rubles .;
  • hinges on the gates (4 pieces) and the gate (2 pieces), and that another 1,000 rubles.
  • Ruberoid - 3 rolls - 615 rub .;
  • boards (formwork) - 300 rub .;
  • Screws metal 39h4 mm - 300 pieces - 100 rub .;
  • Roofing screws 4,8h19mm (RAL8017 and galvanized) - 750 pcs.- 1050 rubles .;
  • Aluminum Rivets 4,8h8 mm - 2 pack.x 50 pcs.- 50 rub .;
  • Aluminum Rivets 4x6 mm - 4 pack.x 50 pcs.- 100 rub .;
  • electrodes (dia. 2-3 mm) - 5 packs - 300 rub .;
  • Cement M500 (7 bags of 50 kg) - 1800 rubles .;
  • threaded pins (tie to form panels) - 120 rub .;
  • Boer two cutters - 1 pc.- 1300 rub .;
  • two-wheeled wheelbarrow with a deep tray - 1 pc.- 2200 rubles .;
  • Laser builder planes (Robotoolz) - 1 pc.- 6000 rubles .;
  • Water level - 1 piece.- 50 rub .;
  • Blind river tongs with a swivel head and nozzles - 1 pc.- 230 rub .;
  • Rubble - (ZIL "uppers") - 3800 rubles .;
  • Sand - (ZIL "uppers") - 2200 rubles .;

Total: 69924 ruble

Upon completion of the fence of corrugated board survived two storms and did not hurt