In the country we do bookcase

By Admin | Furniture For Garden
20 April 2016
When a city dweller gets dacha he wakes up long-dormant desire to do something with their hands.Some are building a house, the other under the force of the toilet or furniture, but there are real craftsmen, such as forum member "Home and Cottage» dim-dim who gladly and competently, professionally and create furniture for questioning.

Bookcase

Let's start with the fact that dim-dim it is made from chipboard veneered oak and oak from the most.

First you need to make a drawing with the dimensions of the future product.Then cut particleboard panels.This can be done in two ways: cut yourself or order sheets, cut to size.

purchasing necessary materials to drill holes for dowels.To do this accurately marked and carefully Drill holes.

Who likes rectangular ends in chipboard panels can just paste over their veneer.And if not, then you need to prepare rack of oak, glued them to the ends of the panels so that later they can be - or have been rounded to reshape.

Preparation rails

example taken oak board
s 30 mm thick and 3 meters long.Need a rake of 1.5 m and for that of the board saw off workpiece 1.6 meters.Chipboard panel has a thickness of 26 mm, so the rail is necessary to adjust the size.For this purpose the sawing machine, the guide and a template to which the board is fixed.Template size: width 180 mm, length 2000 mm.and thickness of 20 mm.With the help of screws you need to fix the board to the pattern and moving the template along the rail to cut exactly one edge of the oak planks.Thus, all the boards are equal.During the cutting of the pattern is under the board.



The next phase is removed and the guide pattern is exposed to the size of the future strips.That is, 25 mm.± 1 mm.and a second dimension of 15 mm.± 1 mm.and cut the required number of strips.These slats must be passed through the planer (surface gauge) or electric plane, thus it is necessary to be very careful to make the two sides, who snapped the machine parallel to each other.We have two sides of the processed and two untouched.Then rails are polished, can be using the machine fixed on the table.

Grinding need to remove the waves after the gauge, because they will interfere when milling (to be repeated waves) when using the cutter bearing.
After training they need to glue the strips to the DSP, for this purpose, clamp the required length.To avoid pushing the workpiece clamping is necessary before it clamps beneath the veneer top 5 for example.Pasting long countertops require clamps or special edge.Edge expensive, but compact.



During clamp parts of the glue joints may go then take a rag and wipe without smearing the entire part.Or let the glue is dry, and then you remove it easily chisel.

adhesive that uses dim-dim it very much.It is transparent when dry, good wood glue and is not afraid of moisture.In addition, the adhesive has plenty of other good, important to read the instructions before using.



Reiki on the table is better to join at an angle of 45 degrees.At first cut, and then pasted.With belt sander removes it "thresholds" between the DSP and the rack.

milling ends

When milling ends nothing complicated, you only need to choose the right cutter for relief, put the necessary "flight" mills and passed through a mill blank so that it did not go in spurts and not drift apart.

When processing the first difficulty is your irrepressible imagination to be on something to stop.The second difficulty "departure cutters."When installing the cutter, check out how it works on unnecessary pruning.You can adjust the size of the job for all the rails.

The picture you can see that the working of the mills in the upper part moves away from the workpiece at 0.5 mm.These gaps need to clean up.After milling walk sandpaper with grain 150 on the workpiece.These differences better otherwise smooth varnishing after they occur and will "throw you in the eye."



photos manufacture skirting plinth cabinet.For this cabinet milled ends the same way.


rear wall of the cabinet

Her dim-dim made of 4 mm.plywood.He had not planned to cover the entire back of the cabinet, so cut some plywood strips and closed where it was needed.You can use the sawing machine and jigsaws.After sandpaper chamfer.This is because the tree keeps bad angles and still rounded.You can use sandpaper 150 and walk a couple of times.

Manufacturing basement part

For this purpose, particleboard and plywood.DSP performs the role of the lower shelf and the bottom of the cabinet, and plywood is used to lift the bottom of the floor.To do this, cut strips of plywood (20 mm.), They are placed on the perimeter and attached with dowels and glue to the chipboard.



cabinet assembly


preliminary until done back wall, rack clamps clamped to it is less than staggering.Then gather all the details of the cabinet, and checked the accuracy of all the details.Then he understands, varnished all its parts disassembled, and remain dry.Details lacquered in several stages.First, a first layer coated with a varnish and then sanded cloth cover 320. Then the second time.

When all the parts of the cabinet will dry it is collected.dim-dim in the manufacture of the cabinet did not use the tie, only dowels.His bottom and countertop are ties for walls and partitions, and the rear wall of plywood cabinet gives the necessary rigidity and a wardrobe is not swinging.



Previously, he planned to make a cabinet with doors, but then changed his mind and decided that it shelves for books.

That's all.Good luck everyone!

Posted party forum "Home and Cottage» dim-dim
Editor: Roman Adamov